How to Replace a Kia Sportage Replacement Key

For a number of Kia models keys, the key has an integrated keyless entry system. The key functions like an remote control and can be exchanged with an Kia dealer.

Key fobs may stop working for several reasons, including a dead coin battery, worn buttons signal interference, water damage, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How to replace a remote key or smartkey

If your Kia is equipped with an intelligent key, remote key, push-to-start keys, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacement. This is particularly in the event that your vehicle displays a message that indicates that the smart or remote key is not powered by the battery.

Fortunately, it's quite simple to do. To replace the battery on the keyfob remove your mechanical key from the slit at the back of the fob. Then, push the cover open. Inside the key fob, there will be tiny screws that hold the battery in its place. Remove the old battery by detaching the screw using a small screwdriver. Insert the new battery and then close the slit on the key fob.

Test the key fob by pressing the lock or unlock buttons. You're good to go when the doors lock or unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need to note the key code number on the key code tag.

How do I replace a battery

If the Kia key fob doesn't respond when you press the lock/unlock button, it is likely that the battery is insufficient. A low battery could cause other problems like the check engine light flashing on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires only a few tools.

Before you begin the process ensure that your vehicle is turned off and that all doors are shut. Find the small metal or plastic piece at the bottom of your key fob, and move it until a metal key is released. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover on the rear and use a plastic pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery, and then align the new one so that the "+" positive side faces your face and the "negative" negative side is facing the fob's electrical contacts made of metal. Push the new CR2032 battery straight into place without putting too much force on it to avoid damaging or programmers bending the contacts of the metal.

Once the new battery has been installed, turn the key fob off and on in the ignition repeatedly until the door locks cycle. Then, test your kia sportage key key fob to see whether it's functioning properly again.

How do you replace the smart key?

There is a possibility of having a standard keyfob or a Smart Key based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs contain an internal battery that will eventually need to be changed. This is a simple procedure which takes just two minutes.

Be sure to switch off your Kia and be on a level or well-lit surface prior to when you begin. Remember that the fob contains tiny parts that could fall when you're not careful.

The release button for the small size is located on the lower backside. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery is CR-2032, and can be bought on the internet or at your local auto parts store. When you're done, the key fob will allow you to lock or unlock and start your vehicle even if it's not running.

How do you replace a mechanical key

The Kia key fob is an amazing convenience that allows us to lock and unlock our car with the press of an button. But like any device it may have issues at times. There are ways to solve these issues and keep your key fobs working for an extended period of time.

A dead or weak battery is one of the most common problems. This can cause your fob to stop working or work intermittently. If this is the case then try replacing the battery with a new one.

If this isn't enough to resolve the problem Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new one.

Once the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit in the slot). Test the fob to make sure it's functioning properly. If the fob still isn't working, call a locksmith or dealer to resolve the issue. Make sure they make you an emergency key that works in all the door and trunk cylinders to prevent lockouts in the future.