Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are long-lasting, durable and easy to maintain. Unlike timber and aluminium, they don't get rusty or decay.

It is essential to clean and oil UPVC doors and windows regularly. This will help avoid unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, which can make it very dangerous and potentially fatal. It is important to ensure that your windows are in good working order.

For single pane windows, it is relatively easy to replace them, and the replacement will usually fit inside the old frame very easily. If you have double-paned windows that are joined by internal beading, it is more difficult to remove and replace the panes that were previously in use. In this situation it is essential to buy plastic spacers to aid in fitting the new pane into the window frame.

If you plan to try to remove the glass panes yourself it is important to wear the proper safety gear that includes gloves with a thick layer of material and eye protection. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards of glass fall onto the fabric and not on the floor and could be trampled under.

After the glass has been removed, it's a good idea to seal the gap with some clear packaging tape or uPVC window repairs duct tape to stop drafts and water from entering the property until a professional comes out and fix the window. It also acts as a barrier to prevent any criminals from getting into your home. If the gap between the door and the window is large, you might prefer security screens that includes an opening. This will provide the best of both.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash window. However, over time they may be afflicted by a variety of issues, including sliding. A sagging uPVC window can cause problems with light, draughts, and even security. It's important to take action immediately if you notice your uPVC windows are sliding.

Repositioning the hinges can help fix a window that is sagging. To do this, you'll need to open the window so that you can access the frame. With an screwdriver, remove the top and bottom hinges and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you have repositioned your hinges. If you're satisfied with the fit, tighten the screws to ensure that they stay in place.

If you cannot reposition the hinges, you might need to replace the seal. As time passes, rubber seals lose their elasticity and dry out, which causes them to loosen. It is crucial to replace your seal as soon as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles may also become loose. Most often this is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has worn out. It's relatively simple to repair a loose uPVC handle. First, you'll need close the window and then perform a test fit. The corners of the sash should align with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and then return the mechanism to its original the position it was in.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains, it's crucial to take action. Water leaks through windows can cause structural damage to your home and affect your ability to regulate the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame has been damaged or is missing.

This is a relatively easy fix that can be completed by any competent DIYer. Depending on the severity of the problem the caulking used previously may require removal before a fresh layer can be applied. It is essential to keep in mind that when it is about upvc window Repairs (www.repairmywindowsanddoors.co.uk), you should not be tempted to 'over-caulk' as this will only make the area harder to clean and can reduce your energy efficiency.

It is crucial to make sure that any drainage holes are clear of debris and that the sill pan is placed in a way that allows it to drain away from the window. In more serious situations, you may need to think about replacing the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in damp conditions and can quickly spread throughout the house.

If the leakage occurs between the double-glazed glass it is more likely that the problem is with the seal rather than the frame. A uPVC specialist can easily solve this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open or it opens with an ease. Any competent DIYer can replace these in a matter of minutes.

Most households in the UK will have either top hung or side hung uPVC windows that use hinges and like any mechanical part they will wear out over time. It's easy to change a window hinge however it is easier if someone else helps hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrow on each hinge, this shows which way the window should be opened.

The issue can be caused due to opening the window in the wrong way or by a poor installation at the factory. This issue can be fixed by sending us a photo via our website and we will be pleased to offer you suggestions.

Regularly lubricating the hinges is essential. Applying a light engineering lubricant on the hinges is a great method to accomplish this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and reduce the possibility of sticking. Ideally, you should perform this every year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. The hinges can also be disaligned as a result of wear, causing a gap where the sash and frame meet. If they are beyond repair, it may be required to realign them. The second is the interlock, which is located on the hinge of the window, may also become misaligned, again it may be possible to just give them a thorough clean, however in some cases it might be necessary to have them replaced.

These seals are susceptible to wear and tear or become damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping is a good way to stop draughts. Replace the upvc windows with low-emissivity glasses. This will help regulate indoor temperatures and lessen the possibility of draughts.

Another, and most effective ways to cut down on draughts is by using a draught excluder. These are typically fabric tubes filled with some type of filler. They can be put on top of your windowsill. They can keep your home warm by blocking out cold air.

Your windows made of upvc will remain a great source of insulation and security in your home with regular maintenance and repairs. It is crucial to recognize that all windows have a life span and they may reach an point at which it is more economical to replace them than repair them. So, if you're experiencing problems with your upvc windows, it is best to seek professional assistance as soon as you can.