Double Glazing Door Lock Repairs

Are your uPVC door or window mechanism faulty? Perhaps the door or window handles aren't able to connect correctly or are difficult to use.

You'll lose energy if your double-glazed doors don't work properly. This also increases the likelihood of burglaries. Owen the Locksmith will be able to repair your door lock at reasonable costs.

Snapped Key

When a key snaps off inside a lock, it could be incredibly frustrating. It can also be a security risk, as it may make you vulnerable to burglars if your door does not lock. Fortunately, there are simple fixes you can try to resolve the issue and get your door operating properly once more.

Be sure to remain calm. If you panic, you could end up pushing the damaged key further into the lock.

Spray WD-40, or another penetrating lubricant, into the lock. This will help the broken piece emerge more easily. You can also use the screwdriver to break off any pieces that are stuck. If you happen to have a bit of the key left visible it, you can use a paperclip or some other metal object that is thin to grab it and pull it out. Both methods work well, however, be careful not to push the broken piece of the key further into the keyway.

Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't have any of these then you can bend a hook using needle-nosed pliers. Finally, a pair of tweezers can be used to grip and remove the remaining piece of the key that was broken.

If you are unable to get the broken piece of the key out, try using a lock de-icer. It is available in most hardware stores and works by freezing any moisture present in the lock.

If none of these solutions seem to work, it may be time to call a locksmith. Fitlocks experts can quickly fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also reconfigure the double glazing door mechanisms so that they are more easy to operate. Get a double glazing repair via our website or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can be an extremely risky security issue. It's fortunately a simple repair for an expert locksmith to complete. A locksmith will have to tap the cylinder to fix it. This can be done with a hammer or other tool. However, the best method is to use a wire or a long match. Then, place the match's tip or wire near the keyway. The locksmith can then strike the lock to break it. This is more secure than using the hammer, which could damage the lock.

The most common cause of cracks in the cylinder head is overheating. This can occur when the block and cylinder head are made of different metals such as cast-iron and aluminum. When the various metals heat up and cool down at different rates, it may create hotspots in the local area that expand faster than the rest of the cylinder head, leading to cracks.

Another reason that could cause cylinder cracks is corrosion. If the head and block of a cylinder are not maintained correctly they could be corroded or rust and Upvc repairs near me cause them to expand more than they would normally. This can cause cracks in the future.

If your uPVC window or door lock is brittle and requires a lot more pressure to turn, it could be due to a variety reasons. A defective locking mechanism, misalignment or the wear of the handle are typical reasons for this issue.

This is a straightforward and cost-effective fix that a majority of double glazing owners can accomplish. A professional locksmith should be able to solve the issue within an hour after arriving at your residence. They can replace the locking mechanisms, or replace the window handles and replace the gearboxes, depending on the specific requirements of your home. A skilled locksmith will always be able to inform you of the most cost-effective solution for your home. They can even suggest upgrades to high-security 3 Star TS007 euro cylinders that will give you an additional layer of protection against burglars. This is a small price to pay for the peace of mind that comes with knowing your uPVC doors are safe.

Broken Handle

It's not surprising that window handle locks could break. They are equipped with complex mechanisms that become less effective over time. If yours breaks it's difficult to identify the cause of the issue and make sure that you repair it correctly.

Fixing your broken handle, whether it's an internal latch or the locking mechanism, will improve the security of your uPVC door and prevent draughts. It could be costly to repair or replace your handle if it is not done correctly and can also damage the frame and the lock of your door.

Screwdriver Open the window and the screw loose, loosen the handle. The screw should be on the inside face of the back plate, which is usually hidden by an aesthetically pleasing cover for the screw reasons. You should not be able to replace any internal parts of the handle, such as the plates and levers on either side. Ideally, keep these in the same place so you can re-install them in the event of a need.

Then, rotate the handle so it's at 90 degrees to the window doctor near me frame. Finally, loosen the screw on the back of the handle that holds it to the internal spindle by using another screwdriver. Once the screw is removed, you should be in a position to pull the handle away and pull out the broken spindle. Replace it with a brand new one, making sure that it is the same length as the old one (you can usually find these on the internet or at hardware stores) and screw it securely in the right place. Do not overtighten the screw as this can cause damage to the handle and window frame.

Check that the new handle is correctly installed, then close and test the handle. It should function smoothly, and you will be able to open your windows once again.

While you're working on the handle, be sure to ensure that your uPVC windows are shut correctly. If they aren't closing properly, you could experience damp or draughts in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can alter the hinges of the frames of your windows to ensure that they close properly.

Broken Spindle

It is usually the case that the spindle in the handle is broken, not the handle itself. This is especially common in upvc Repairs near me tilt and turn windows. These windows require a handle to operate an electronic locking mechanism within the frame of the window. The handle is attached to a central rod which activates locks that are shaped like mushrooms and secure the window frame keep. If the dead latch mechanism does not open after the handle has been turned, it is most likely the spindle is damaged. This could be a frustrating problem.

There are solutions to this issue. A reputable locksmith can quickly and efficiently repair this issue. They will be able to disassemble the window handle by using a tool that can remove the wheel component of the mechanism, where the spindle goes. This is done without damaging the handle or causing other damage to the frame of the window.

After removing the wheel the technician will inspect the spindle and identify the cause of the break. This involves disassembling the spindle and inspecting each component, noting any wear or damage. The process is done in a clean, well-lit room by skilled technicians.

The next step is to clean the damaged spindle. This will remove any dirt or debris which may be obstructing it from functioning normally. The spindle could then be repaired or replaced. If the technician is replacing the spindle, the dowel can be used that is the same size to the original. He will then make holes in the same way into both pieces. This will ensure that the spindle will fit perfectly with the handle.

If the damaged spindle can't be repaired, it could require replacement. Home centres sell generic replacements but if the style of your window is unique then it is necessary to find a woodworker or cabinet maker who can duplicate the exact part for you. Once the new spindle is installed, it can be fitted to the handle by lining up the screw holes on the handle and the frame existing screws. Once the handle is securely set, you are able to operate your uPVC windows.