UPVC Window Handle Replacement

It is easy to repair a damaged window handle with the right tools. It is important to know what kind of handle you have and its spindle size before purchasing a replacement.

Older uPVC windows use handles with cockspurs, which have spurs that protrude to lock over a cockspur wedge striker plate. They can be left- or right-handed and should be compatible when replaced.

What type of lock and handle do I have?

There are a variety of windows locks and handles made of upvc, each with its own advantages and purposes. The type of handle that you have will determine if your locking mechanism is effective and also if it is simple to open the windows. With time and regular use the handles made of upvc on your windows can get worn out and damaged. This makes them less secure and less effective. In some cases they could even disappear completely. It is important to repair the handles on your window made of upvc when you notice them falling off. This will help stop potential burglaries and keep your home safe.

It is a good thing that replacing your upvc window handles is a fairly simple job that can be completed by nearly everyone. With a few basic tools and the right information it's a straightforward procedure that shouldn't take longer than a couple of minutes. To get started you'll need to identify the type of handle and lock you have on your window made of upvc and Window Handle Replacement then find the perfect replacement.

Inline Espagnolette Handles

These are the most commonly used kind of upvc handle and are typically located on the side of your window. They are flat and feature a latch which engages the locking mechanism of the window frame. Inline upvc handles feature a spindle that runs through the middle of the handle to the window frame in order to control the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and feature an distinctive hook-shaped design. Cockspur handles are fitted with a single screw that secures the handle to the frame and aren't as secure as other kinds of window handles.

Handles that can tilt and turn

Unlike the other handles made of upvc that are tilt and turn, these handles can be turned to open the window and tilted inwards to allow ventilation. They have a 7mm spindle at the back and are available both in right and left-handed versions.

When you are purchasing replacement handles for upvc it is essential to measure the spindle's length as not all are the same size. Drop something in the middle of the hole to check the length. This is the largest spindle size that will fit your windows.

What is a spindle?

uPVC window handles function in a similar way to doors. By turning the handle, you will be able to activate a latch inside the frame. The window can then be opened and closed. However, sometimes handles can be damaged, particularly when they are used frequently or exposed to harsh weather conditions. This can leave you needing to replace your uPVC handles on windows since they may not operate the window correctly in the future.

There are many different types of uPVC handle options, including Espag, Cockspur, and Spaded handles. These handles are designed to fit into the uPVC frames in different ways and each handle type utilizes a specific spindle to secure the mechanism into the window. It is important to identify the kind of handle that is installed on your uPVC windows to ensure that you replace it with the right one.

The base section of the handle will tell you what kind of uPVC it is. There should be a "snap in cover' over one screw which holds the handle base in place. Once you remove this, you will be able see the second screw that holds the base of the handle in position. After both screws have been removed, you should be in a position to pull the handle away from the uPVC window.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You will need to purchase a new one that is the same length as the handle that was originally used and locking device.

The spindle wears down and is unable to operate the locking mechanism. This could be due damage caused by constant use, a loosening of the locking mechanism or even corrosion that occurs over time. If this occurs, it is required to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I remove the old handle?

window replacement cost uk handles can become damaged or even broken over the course of time. It is crucial to repair them as quickly as you can to ensure your security. It is simple to replace a damaged or worn handle. The job can be accomplished in less than one minute without the need for any special tools.

The first step in removing the handle that was previously used is to remove the screw situated on the top of the base of the handle. Once this is removed the handle can then be removed from the base section. A second screw will be located at the base of the handle. It can also be removed. After both screws are removed, the handle can be removed from the base section of the window.

After the handle has been removed, you can take the new handle and line up the fixing holes with the holes that are present in the window frame. If there is a sticker or cap on the new handle, take it off it if required and screw the handle into place. It is crucial to verify that the handle works once it is put in place. Turn the handle over and make sure the lock mechanism is working.

Espag handles have a spindle which protrudes out of the handle and slots into the multipoint locking mechanism that is on the window frame. Cadenza windows feature a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hang over the frame that surrounds the window or the transom crossmember of the bar.

After you have installed the new handle, place the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) after the handle is securely fixed. When the handle is in use, open and close the window a couple of times to ensure it works properly and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is easy. You only need a screwdriver and a bit of perseverance. The first thing you need to do is to ensure that the handle is locked and then remove any screws that are visible. you can also replace them with screw caps if needed. After the handle has been removed and you are ready to take a note of the length of the spindle that extends from the back of the handle. This is vital because it will determine the kind of handle to purchase.

Espagnolette handles are the most popular type of handle used on uPVC windows. The spindle is inserted into the handle to activate the locking mechanism within the window frame. When the handle is turned, it opens the latch on the window and allows it to open. In regular use and time, espagnolette handles may become damaged.

Cadenza handles are a type of uPVC handle that is typically used with tilt and turn windows. They feature an elongated blade that functions as the multipoint locking mechanism inside the window. They are usually more secure than handles made of espagnolette because they are only accessible from the inside. You can replace them using the same method that you would with espagnolette handles, but make sure the new handle is not angled and flat.

Once you've decided on the correct handle to purchase then you can line up the new handle with the existing screw holes and then screw it into place. After that, you can put the screws on and test the new handle. You can do this by moving the handle back and forth from the locked position to the unlocked one several times. If you experience any issues, it could be worth contacting a specialist to see if they are able to help resolve the problem. They can advise you on how to resolve the problem in a timely and efficient way.