How to Replace a kia picanto key fob replacement (lookingfor.kr) Sportage Replacement Key

For many Kia models keys, the key has a built-in keyless entry system. This key usually resembles a remote control and is able to be replaced with a fresh one from a Kia dealer or a locksmith.

Key fobs are prone to malfunction for several reasons, including the battery of the coin is dead, worn buttons water damage, signal interference, and a defective receiver module. Here are some tips on how you can get your Kia Sportage replacement key working again.

How to replace a smartkey or remote key?

The battery in your Kia's intelligent key will eventually require to be replaced, regardless of whether it is a remote key as well as a push-to start key or a standard metal key that does not contain a transponder. This is especially when the vehicle displays a message that indicates that the remote or smart key has a low battery.

It's a simple process. To replace the battery in the key fob remove the mechanical key from the hole in the back of the key fob. Then lift the cover. A small screw is located inside the key fob to keep the battery in the correct position. Remove the old battery by unscrewing the screw using a small screwdriver. Insert the new battery and then close the slit on the key fob.

When the key fob is equipped with a fresh battery check it by pressing the lock and unlock buttons. If the doors lock and unlock as expected, then you're good to go! You can now use the hands-free feature to lock and unlock your Kia when your fingers get cold or you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming done. This requires a special programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll have to write down the key code's number on the key code tag.

How do you replace a battery?

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A battery that is not functioning properly can cause other issues, such as the check engine light flashing or the engine not cranking properly. Fortunately replacing the key fob battery is a relatively simple DIY project that requires only the most basic tools.

Make sure you turn off your vehicle and shut all doors prior to starting. Find the small, metal or plastic piece that is located at the bottom of the key fob. Then, jiggle it until the key falls out. You can then insert the key into the handle of the door for the driver to unlock your car.

To replace the key fob battery, take off the cover from the back and use a pry bar tool to remove the latch holding the black negative battery cable. Remove the old battery and align the new battery in a way that the "+" positive side faces you and the "negative" negative side is facing the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts made of metal.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks cycle. You can then test the Kia's key fob to ensure it's functioning properly.

How do you replace the smart key?

Depending on the model of your kia sportage key Sportage, you may have a standard key fob or a smart key. The smart key has an embedded mechanical key blade, while the standard key fob does not. Both types of key fobs are equipped with batteries inside that eventually will need to be replaced. Luckily, this is an easy process that only takes about two minutes.

Be sure to turn off your Kia and stand on a flat and well-lit surface prior to you begin. Remember that the fob has tiny pieces that could fall should you not be careful.

The release button for the small size is located on the lower backside. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery is CR-2032, and can be purchased online or in your local auto parts shop. After you've finished, your key fob should be able to lock and unlock your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia keyfob is a great convenience that allows us to lock or unlock our car with just pressing a button. Like all devices that is used, the Kia key fob might have issues. There are steps to take to troubleshoot these issues and ensure that our key fobs are in good condition over the long haul.

A dead or weak battery is among the most common problems. This could cause your device to stop working or work intermittently. If this is the case you should replace the battery a new one.

If this isn't enough to solve the issue, you can use an ordinary screwdriver with a flat head to wedge the plastic casing of the fob open. Be careful not to scratch any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery that was removed and replace it with a brand new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob to ensure it's working properly. Contact a dealer, or a locksmith to solve the issue in the event that the fob is not working. To avoid lockouts in the future, make sure you get an emergency key that can work in all of the trunk and door cylinders.